TRUSTING ORCHIDEE_2_2 at Jean-Zay/IDRIS

Started 2022, still in use

This is a program testing the different revisions on the branch of ORCHIDEE_2_2. Different compile options and run modes are tested offline and coupled to LMDZ. Restart files and diagnostics are compared to a reference run. Intercomparison of some runs are done.
Each line in the grey table corresponds to a specific installation of the model and all related tests. The revision number of ORCHIDEE is set in column 2 and the revsion numbers for the other compontents and tools are listed in the end of the line. The fifth column shows the reference revision which is used for comparing.
When the Status field in the third column is green and says OK it means that all tests finished well and there were no changes compared to the reference run. When the status field says DIFFER it means that all tests finished but all the results changed. When the Status field becomes red saying FAILED their might be several reasons, read the comments in fourth column to know more. There might be some runs that are not counted for in the Status field.

At Jean-Zay, the trusting do not check the diagnostic output files. It checks the restart files only

See here the discription of the different test cases performed at each execution of the trusting. Default set up is used if nothing else is said.

Offline =>

JobName

Compilation

Experiment Type

PeriodLenght

Total lenght

Other

LMDZOR =>

JobName

Compilation

Experiment Type

Parallelization

PeriodLenght

Total lenght

Other

O1p

prod

OOL_SEC_STO_FG2

1Y

2Y

LO1p

prod

clim_pdControl

mpi_omp

1D

2D

O2p

prod

OOL_SEC_STO_FG2

1M

2Y

LO2p

prod

clim_pdControl

mpi_omp

2D

2D

O3p

prod

OOL_SEC_STO_FG2

1Y

2Y

Using different nubmer of cores MPI

LO3p

prod

clim_pdControl

mpi_omp

1D

2D

Using different number of cores MPI

O4p

prod

OOL_SEC_STO_FG2nd

1Y

2Y

LO4p

prod

clim_pdControl

mpi

1D

2D

O5d

debug

OOL_SEC_STO_FG2

1D

4D

LO5d

debug

clim_pdControl

mpi_omp

1D

2D

O6d

debug

OOL_SEC_STO_FG2

2D

4D

LO6d

debug

clim_pdControl

mpi_omp

1D

2D

Using different number of cores MPI

O7d

debug

OOL_SEC_STO_FG2

2D

4D

Using IOIPSL output

LO7d

debug

clim_pdControl

mpi_omp

1D

2D

Using interpolation with XIOS

O8d

debug

OOL_SEC_STO_FG2

2D

4D

Using interpolation with XIOS

O9d

debug

OOL_SEC_STO_FG2

2D

4D

OK_SOIL_CARBON_DISCRETIZATION=y

O10d

debug

OOL_SEC_STO_FG2nd

1D

4D

O11d

debug

OOL_SEC_STO_FG2nd

2D

4D

O12d

debug

--

On the 28th of May 2023, some of the test cases changed set up. See below the prevous description of these test cases:

Offline =>	JobName	Compilation	Experiment Type	PeriodLenght	Total lenght	Other
	O4p	prod	OOL_SEC_STO_FG3nd	2D	4D
	O10d	debug	OOL_SEC_STO_FG4	1D	4D
	O11d	debug	OOL_SEC_STO_FG4	2D	4D
	O12d	debug	OOL_SEC_STO_FG3nd	2D	4D	On regional domain

Note 1 New driver does not give the same restart using different execution lenght: 1+1 is not =2 using ORCHIDEE_2_2. This is not a new problem but previsously it was not tested in the trusting. That's why O10d is different from O11d.